View UPG2415TK_6355003.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

caution although this device is designed to be as robust as possible, esd (electrostatic discharge) can damage this device. this device must be protected at all times from esd. static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. industry - standard esd precautions must be employed at all times. 0. 5 to 6 .0 ghz spdt switch gaas integrated circuit ? pg2 4 15 t k document no. pg10 7 93 ej0 1 v0ds ( 1st edition) date published february 20 10 ns description the ? pg 24 15 tk is a gaas mmic spdt ( s ingle p ole d ouble t hrow) switch for 0.5 to 6.0 ghz applications, including dual - band wireless lan . this device operate s with dual control switching voltage s of 2. 7 to 5.3 v. this device can operate at freque nc ies from 0. 5 to 6 .0 ghz, with low insertion loss and high isolation. this device is housed in a 6 - pin lead - less minimold package ( 1511 pkg ) a nd is suit able for high - density surface mounting. features ? switch control voltage : v cont (h) = 3.0 v typ. : v cont (l) = 0 v typ. ? low insertion loss : l ins = 0. 4 5 db typ. @ f = 2.5 ghz : l ins = 0. 65 db typ. @ f = 6.0 ghz ? high isolation : isl = 2 8 db typ. @ f = 2.5 ghz : isl = 26 db typ. @ f = 6.0 ghz ? h andling power : p in ( 0. 1 db) = + 31 .0 dbm typ. @ f = 2 . 0 to 6 .0 ghz ? high - density surface mounting : 6 - pin lead - less minimold package ( 1.5 ? 1.1 ? 0.55 mm ) applications ? dual - band wireless lan etc. ordering information part number order number package marking supplying form ? pg 24 15t k - e 2 ? pg 24 15 tk - e 2 - a 6 - pin lead - less minimold (1511 pkg) (pb - free) g 6d ? embossed tape 8 mm wide ? pin 1, 6 face the perforation side of the tape ? qty 5 kpcs/reel remark to order evaluation samples, please contact your nearby sales office. part number for sample order: ? pg 24 15 tk - a
data sheet pg10 7 93 ej0 1 v0ds 2 ? pg2 4 15 t k pin connections and internal block diagram pin no. pin name 1 rf1 2 gnd 3 rf 2 4 v cont 2 5 rfc 6 v cont 1 sw truth table on path v cont 1 v cont 2 rfc - rf1 high low rfc - rf2 low high absolute maximum ratings (t a = +25 ? parameter symbol ratings unit switch control voltage v cont + 6.0 note v input power (v cont (h) = 3.0 v) p in + 34.0 dbm input power (v cont (h) = 5.0 v) p in + 35.0 dbm power dissipation (average) p d 0.15 w operating ambient temp erature t a ? 4 5 to +85 ? c storage temperature t stg ? 55 to +1 50 ? c note ? v cont 1 ? v cont 2 ? ? 6.0 v recommended operating range (t a = +25 ? parameter symbol min. typ. max. unit operating frequency f 0.5 ? 6 .0 ghz switch co ntrol voltage (h) v cont (h) 2. 7 3.0 5.3 v switch control voltage (l) v cont (l) ? 0.2 0 0.2 v control voltage difference ? v cont (h) , ? v cont (l) note ? 0.1 0 0.1 v note ? v cont (h) = v cont 1 (h) ? v cont 2 (h) ? v cont (l) = v cont 1 (l) ? v cont 2 (l)
data sheet pg10 7 93 ej0 1 v0ds 3 ? pg2 4 15 t k electrical characteristics (t a = +25 ? cont (h) = 3.0 v, v cont (l) = 0 v, z o = 5 0 ? parameter symbol test conditions min. typ. max. unit insertion loss 1 l ins 1 f = 0.5 to 2 . 0 ghz note 1 ? 0.40 0. 6 5 db insertion loss 2 l ins 2 f = 2 . 0 to 2 . 5 ghz ? 0.4 5 0. 70 db insertion loss 3 l ins 3 f = 2 . 5 to 3 . 8 ghz ? 0. 55 0. 80 db insertion loss 4 l ins 4 f = 3 . 8 to 6 . 0 ghz ? 0. 65 0. 90 db isolation 1 isl1 f = 0.5 to 2.0 ghz note 1 25 28 ? db isolation 2 isl2 f = 2.0 to 2.5 ghz 25 28 ? db isolation 3 isl3 f = 2.5 to 3.8 ghz 25 28 ? db isolation 4 isl4 f = 3.8 to 6.0 ghz 22 26 ? db return loss 1 rl1 f = 0.5 to 2.0 ghz note 1 15 20 ? db return loss 2 rl 2 f = 2 . 0 to 2 . 5 ghz 15 20 ? db return loss 3 rl 3 f = 2 .5 to 6 . 0 g hz 1 0 15 ? db 0.1 db loss compression p in (0.1 db) f = 0.5 to 2.0 ghz note 1 ? +32.0 ? dbm input power note 2 f = 2.0 to 6.0 ghz ? + 31 .0 ? dbm f = 0.5 to 6.0 ghz note 1 , v cont (h) = 5.0 v ? +35.0 ? dbm 1 db loss compression p in (1 db) f = 0.5 to 2. 0 ghz note 1 ? + 34 .0 ? dbm input power note 3 f = 2.0 to 6.0 ghz ? + 34 .0 ? dbm input 3rd order intercept point iip 3 f = 2 .5 ghz, p in = +20 dbm ? +60 ? dbm 2nd harmonics 2f 0 f = 2.5 ghz, p in = +20 dbm ? 80 ? dbc 3r d harmonics 3f 0 f = 2.5 ghz, p in = +20 dbm ? 80 ? dbc switch control current i cont no rf input ? 0. 1 1 0 ? a switch control speed t sw 50% ctl to 90/10% rf ? 50 2 50 ns note s 1. dc blocking capacitors = 56 pf at f = 0. 5 to 2 . 0 ghz 2. p in (0.1 db) is the measured input power level when the ins ertion loss increases 0.1 db more than that of the linear range. 3. p in (1 db) is the measured input power level when the insertion loss increases 1 db more than that of the linear range. caution it is necessary to use dc blocking capacitors with this de vice. the value of dc blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system.
data sheet pg10 7 93 ej0 1 v0ds 4 ? pg2 4 15 t k evaluation circuit note c 1 : 0.5 to 2 . 0 ghz 56 pf : 2 . 0 to 6 .0 ghz 8 pf c2 : 1 000 pf the application circuits and their parameters are for reference only and are not intended for use in actual design - ins application information ? l esd provides a means to increase the esd protection on a specific rf por t, typically the port attached to the antenna. ? the value may be tailored to provide specific electrical responses. ? the rf ground connections should be kept as short as possible and connected to directly to a good rf ground for best performance .
data sheet pg10 7 93 ej0 1 v0ds 5 ? pg2 4 15 t k illustration of the test circuit assembled on evaluation board using the evaluation board symbol test conditions values c1 f = 0.5 to 2 . 0 ghz 56 pf f = 2 . 0 to 6 .0 ghz 8 pf c2 1 000 pf
data sheet pg10 7 93 ej0 1 v0ds 6 ? pg2 4 15 t k typical characteristics (t a = +25 ? cont (h) = 3.0 v, v cont (l) = 0 v, z o = 5 0 ? remark the graphs indicate nominal characteristics.
data sheet pg10 7 93 ej0 1 v0ds 7 ? pg2 4 15 t k remark the graphs indicate nominal characteristics.
data sheet pg10 7 93 ej0 1 v0ds 8 ? pg2 4 15 t k mounting pad layout dimensions 6 - p in lead - less minimold (1511 pkg) (unit: mm) remark the mounting pad layout in this document is for reference only.
data sheet pg10 7 93 ej0 1 v0ds 9 ? pg2 4 15 t k package dimensions 6 - pin lead - less minimold (1511 pkg) (unit: mm)
data sheet pg10 7 93 ej0 1 v0ds 10 ? pg2 4 15 t k recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact your nearby sales office. soldering method soldering conditions condition symbol infrared reflow peak t emperature (package surface temperature) : 260 ? c or below time at peak temperature : 10 seconds or less time at temperature of 220 ? c or higher : 60 seconds or less preheating time at 120 to 180 ? c : 120 ? 30 seconds maximum number of reflow processes : 3 time s maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ir260 wave soldering peak temperature (molten solder temperature) : 260 ? c or below time at peak temperature : 10 seconds or less preheating temperature (package surface temperature) : 120 ? c or below maximum number of flow processes : 1 time maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ws260 partial heating peak temperature ( terminal temperature) : 350 ? c or below soldering time (per side of device) : 3 seconds or less maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below hs350 caution do not use different soldering methods together (except for partial heating).
data sheet pg10 7 93 ej0 1 v0ds 11 ? pg2 4 15 t k caution gaas products this product uses gallium arsenide (gaas). gaas vap or and powder are hazardous to human health if inhaled or ingested, so please observe the following points. ? follow related laws and ordinances when disposing of the product. if there are no applicable laws and/or ordinances, dispose of the product as rec ommended below. 1. commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. exclude the product from general industrial waste and household garb age, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. ? do not burn, destroy, cut, crush, or chemically dissolve the product. ? do not lick the product or in any way allow it to enter the m outh.

▲Up To Search▲

Price & Availability of UPG2415TK

	To Download UPG2415TK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .